1 1

22" Glitter DTF Gang Sheet (CLASSIC BUILDER)

22" Glitter DTF Gang Sheet (CLASSIC BUILDER)

$39.60 USD
$39.60 USD
Sale Sold out
Size
Classic Shopify Gang Sheet Tool (+10%)
View full details

Fresh Prints press guide

What is Glitter DTF?

A specialty, full-color DTF transfer with visible sparkle built across the printed artwork. The white underbase and adhesive arrive ready to press—so you get bright color, fine detail, and glitter impact without vinyl cutting, weeding, or color-by-color layering.

Full colorBuilt-in sparkleNo weedingCold peel
Fresh Prints Glitter DTF transfer, heat press, and finished glitter shirt
Sparkle built in
cold peel
01

Full-color sparkle

Fine detail, gradients, a bright white underbase, and visible glitter in one finished transfer.

02

No weeding

Trim apart the transfers you need, then place, press, and peel—no vinyl weeding required.

03

Made to stand out

Ideal for spirit wear, dance teams, boutiques, celebrations, and statement graphics.

04

Cool completely

This specialty film is cold peel only. Let it cool fully before removing the carrier.

Start here

Fresh Prints Press Tips

These are starting settings for our Glitter DTF transfers. Heat presses and garments vary, so test unfamiliar fabric and follow the garment care label.

Cotton + 50/50320–325°FStart at the lower end when testing a new garment.
Poly + synthetics280–300°FStart low to reduce scorch marks and dye migration.
Press time10–15 SECUse one complete press without lifting early.
PressureMED–FIRMEven pressure matters more than forcing maximum pressure.
Peel methodCOLD PEELWait until the transfer and carrier are completely cool to the touch.

Finish strong: after peeling, cover the design with parchment or the approved cover sheet and post-press for 5 seconds.

Four-step application

Protect the sparkle.

The repeatable cold-peel workflow for clean edges, strong adhesion, and a consistent glitter finish.

Black and white shirts positioned on a dual-platen heat press01

Prep the garment

Move seams, collars, pockets, buttons, and zippers off the platen. Pre-press for 3–5 seconds to flatten the fabric and remove moisture.

Fresh Prints Glitter DTF transfer positioned on a black shirt before pressing02

Position the transfer

Place the printed adhesive side against the fabric. The artwork should read correctly through the clear carrier. Keep the glitter surface clean and every part of the design on a flat pressing surface.

Heat press engaged on a Fresh Prints Glitter DTF transfer03

Press evenly

Apply the correct temperature, 10–15 seconds, and medium-to-firm pressure. Do not open the press early, slide the garment, or let a seam steal pressure from the design.

Fresh Prints Glitter DTF carrier film peeled from a finished black shirt after cooling04

Cool, peel + finish

Move the garment to a flat surface and let the transfer cool completely. Peel the carrier low and steadily. If any area lifts, stop, lay it back down, repress, and cool fully before trying again.

Do this

Build a repeatable press routine.

  • Test unfamiliar garments and presses.
  • Verify the platen is actually at temperature.
  • Keep the print area flat and obstruction-free.
  • Cool completely, then peel low and steadily.
  • Complete the covered 5-second post-press.

Avoid this

Do not guess through a failure.

  • Do not warm peel or hot peel Glitter DTF.
  • Do not press over collars, seams, or zippers.
  • Do not pull the carrier straight upward or rip through lifting artwork.
  • Do not press a damp or wrinkled garment—pre-press it first.
  • Do not wash, stretch, or heavily handle the garment for 24 hours.

After pressing

Make the print last.

  1. 24 HRWait before the first wash.
  2. INSIDE OUTWash cold on a gentle cycle.
  3. LOW HEATAir dry when possible or tumble dry low.
  4. NO DIRECT IRONKeep high heat off the transfer face.